The FNIRSI 1014D is a compact digital oscilloscope designed for electronic service, research and development departments, technical education and hobbyists. It allows simultaneous analysis and signal generation, which significantly increases the range of applications when diagnosing circuits, testing prototypes or learning to work with waveforms. The device has two input channels with 1 MΩ impedance and supports a bandwidth of 100 MHz at 1GSa/s sampling. A 7-inch LCD screen with a resolution of 800×480 px facilitates operation. Auto-analysis, FFT, X-Y mode and cursor recording are possible. There is also a 1GB internal memory with the ability to store up to 1,000 waveforms and 1,000 screenshots, and data can be easily exported to a computer via USB.
A high sampling rate of 1GSa/s and a bandwidth of 100 MHz enable detailed analysis of analog and digital signals. This allows the device to catch even short-term anomalies in the waveform. Trigger modes include Auto, Single, and Normal, allowing the device to capture both interference pulses and regular analog signals, such as sinusoids.
The integrated DDS signal generator supports 14 standard waveforms (including sine, rectangle, sawtooth, triangle), with precise frequency adjustment in 1 Hz increments. The solution used allows generating signals with accurate parameters for testing and simulation. The output frequency range reaches up to 10 MHz (for sine wave), which allows testing a wide range of electronic and signal circuits.
The "capture output" function allows you to save part or all of the actual waveform from the oscilloscope as the generator's output signal. The ability to store up to 1,000 custom signals increases flexibility in testing and analysis. This solution distinguishes the FNIRSI 1014D from classic arbitrary generators, which rely solely on manual signal adjustment.
An integrated high-voltage protection module allows the device to safely measure signals up to 400V (with x10 probe), reducing the risk of damage to the device during measurements in mains-powered systems. The protection function works automatically, so accidental use of the probe without switching to x10 does not risk damaging the equipment.
The 7" TFT color screen with 800x480 pixel resolution provides a clear representation of waveforms. Auto mode and an intuitive interface allow you to quickly get an image of the signal without manual adjustment. Thanks to an intelligent detection algorithm, the device automatically adjusts the trigger level even for waveforms with multiple slopes or the so-called dead zone. Such a solution saves time and avoids interpretation errors. The oscilloscope can store up to 1,000 screenshots and 1,000 waveforms in its 1GB internal memory. The data can be viewed as thumbnails, which facilitates quick viewing and selection. The interface allows users to zoom in, delete and export records without exiting review mode.
The built-in FFT function and X-Y waveform display mode allow you to analyze harmonics and compare the amplitudes and phase shifts of two signals. These are useful tools in the diagnosis of electronic circuits. In addition, the manual cursor measurement mode makes it possible to read the peak value and frequency without the need to recalculate the scale, which increases the precision of analysis even in distorted waveforms. The device uses a special algorithm for decoding the dial signal, eliminating the problem of erroneous readings caused by oxidation or wear of the mechanism. Even when the encoder is damaged, the oscilloscope works correctly.
| Manufacturer | FNIRSI |
|---|---|
| Model | 1014D |
| Channels | 2 |
| LCD screen size | 7 inches |
| LCD screen resolution | 800 × 480 |
| Display technology | LCD |
| Frequency response | 100 MHz |
| Sampling frequency | 1 GSa/s |
| Highest test voltage | 1X: 40V, 10X: 400V |
| Cursor | XY position Y trigger |
| Rolling mode (roll) | Supported |
| Automatic calibration | Supported |
| Waveform recording | 1000 images + 1000 waveforms |
| Waveform management | Supported |
| Voltage accuracy | ±5% |
| Rise time | < 3 ns |
| Memory depth | 240 Kbit |
| Input resistance | 1 MΩ |
| Sensitivity | 50 mV ~ 500 V |
| Time base | 50 s ~ 10 ns |
| Trigger mode | Single / Normal / Auto |
| Trigger edge | Ascending / Descending |
| Coupling | AC / DC |
| Frequency accuracy | ±0,01% |
| Parameters | 12 types |
| Generator | 14 types |
| Capture output | Supported |
| Extension | USB export |
| Power supply | 5V 2A / 3A / 4A |
| Dimensions | 310 × 145 × 70 mm |
Dovanos prie užsakymų nuolat keičiasi dėl riboto jų kiekio
NEMOKAMAS PRISTATYMAS PERKANT UŽ 50 EUR IR DAUGIAU
Nemokamas pristatymas į Omniva paštomatą perkant daugiau nei 50 Eur
Nemokamas pristatymas į LP Express arba Lietuvos paštą perkant daugiau nei 70 Eur
Nemokamas pristatymas į namus ar darbovietę perkant daugiau nei 150 Eur.
PRISTATYMAS Į Express arba Omniva SIUNTŲ TERMINALĄ
Siuntimas kainuoja 2,49 EUR. Į LP Express 3,99
Užsakius iki 14 val., prekes išsiunčiame tą pačią dieną (tik darbo dienomis). Į siuntų terminalą jūsų užsakymas bus pristatytas per 1-3 darbo dienas nuo išsiuntimo dienos. Paštomatas parenkamas automatiškai artimiausias nuo jūsų pateikto adreso.
Nukreipti siuntą į kitą pristatymo vietą galimybės nėra. Siuntą galite atsiimti jums patogiu laiku. Siuntų terminalai veikia 24 valandas per parą.
PRISTATYMAS Į LIETUVOS PAŠTO SKYRIUS
Pristatymo kaina į pašto skyrius – 3,99 EUR.
Užsakius iki 14 val., prekes išsiunčiame tą pačią dieną (tik darbo dienomis). Į Lietuvos pašto skyrius prekės bus pristatytos per 1-3 darbo dienas nuo išsiuntimo dienos.
PRISTATYMAS Į NAMUS AR Į DARBOVIETĘ KURJERIU
Pristatymo kaina - 4,99 EUR
Užsakymą priims kurjeris ir pristatys jums tiesiai į namus ar darbovietę. Dažniausiai tai trunka 1-3 darbo dienas nuo išsiuntimo dienos.
PRISTATYMAS Į UŽSIENIO VALSTYBES
Pristatymo kaina - 6,99 EUR.
Užsakymas išsiunčiamas per 2 darbo dienas. Pristatymo laikas svyruoja nuo valstybės į kurią siunta keliauja. Dažnais atvejais pristatymo laikas yra tik 2-3 dienas ilgesnis nei Lietuvoje.
P.S Pristatymo kaina gali didėti jeigu prekės yra labai didelės arba jų svoris viršyja standartus, kurie nurodyti pristatymo tarnybų puslapiuose. Tokiais atvejais patys susisiekiame ir aptariame situaciją, Jums papildomai nieko daryti nereikia.
